Water Column vs PSI: Why Is Water Column Used for Pressure Measurement?

Water column vs PSI looks like a contest between two units, but it’s really a question of scale. One handles pressures so small you can barely feel them. The other handles pressures that can burst a hose. If you’ve ever read a gas appliance label that says 7 inches of water column, then glanced at a tire gauge reading 32 psi, you’ve already seen both ends of the range.
This guide covers what each unit means, why water column is still the go-to for low-pressure work, how to convert between the two without a calculator meltdown, and where people most often get it wrong.
Disclosure: This page may contain affiliate links. Please see our affiliate disclaimer for more information.
Water Column vs PSI at a Glance
If you only have thirty seconds, this table covers the essentials.
| Feature | Water column (inWC) | PSI |
| What it measures | Pressure, described as the height of a water column it could hold up | Pounds of force on each square inch of surface |
| Typical range | Hundredths of an inch up to about 28 inWC (roughly 1 psi) | About 1 psi up to thousands of psi |
| Best for | Low-pressure gas, ductwork, chimney draft, cleanrooms | Tires, compressed air, hydraulics, water mains |
| Common labels | inWC, in. w.c., inWG, inH2O, WC | psi, psig, psia, psid |
| Metric relatives | mmH2O, cmH2O | kPa, bar |
| Usually measured as | Gauge or differential pressure | Gauge, absolute or differential |
The number to memorize is 27.68. One psi equals 27.68 inches of water column, so one inch of water column is about 0.036 psi. Everything else in this guide grows out of that ratio.
What Is Water Column Pressure?
Water column describes pressure by picturing a tube of water. If a given pressure could hold water up to a height of one inch, that pressure is one inch of water column, written inWC. Two inches of height means two inWC, and so on. It’s a pressure unit that borrows its name from the height of the liquid it can support.
The idea comes straight from the manometer, one of the oldest pressure instruments there is.
How a U-Tube Manometer Works
Picture a clear, U-shaped tube half filled with water. Connect one leg to the pressure you want to measure and leave the other leg open to the room. The pressure pushes the water down on its side and up on the other. Measure the gap between the two water levels and you have the pressure. No springs, gears or batteries involved.
The math behind it is short: pressure equals the density of the liquid, times gravity, times the height difference. Density and gravity are known values, so the height alone gives you the answer. That’s why liquid column instruments have a long history as reference devices in calibration work.
Names and Abbreviations You’ll See
The same unit turns up under a surprising number of labels, which causes plenty of confusion on job sites and spec sheets.
- inWC, in. w.c. and plain WC all mean inches of water column. You’ll see WC stamped on gas valves and regulators.
- inWG and w.g. mean inches of water gauge, which is the same thing.
- inH2O is the version you’ll find on digital manometers and in software.
- mmH2O and cmH2O are the metric cousins, common in medical equipment and European specifications.
- Feet of water, or feet of head, is the same idea scaled up for pumps and plumbing. One psi equals about 2.31 feet of head.
What Is PSI?
PSI stands for pounds per square inch. It’s the force of one pound spread across one square inch of surface. Pump a bike tire to 60 psi and every square inch of the inner wall is being pushed outward with 60 pounds of force.
Three suffixes change what the number means, and mixing them up is a classic mistake.
- psig is gauge pressure, measured relative to the air around you. A tire gauge reads psig, which is why a flat tire reads zero even though air is still inside.
- psia is absolute pressure, measured from a perfect vacuum. The atmosphere at sea level is about 14.7 psia.
- psid is differential pressure, the difference between two points, such as the two sides of a filter.
PSI is the workhorse for anything from a few psi up to thousands: tires, compressed air, hydraulic systems, home water supply and industrial process lines.
Why Is Water Column Used for Pressure Measurement?
There are four reasons, and they stack on top of each other.
Small Pressures Deserve Readable Numbers
Residential natural gas usually reaches an appliance at around 7 inWC. In psi, that’s 0.25. Furnace duct static pressure often sits near 0.5 inWC, which is 0.018 psi. A cleanroom might hold a 0.05 inWC difference between rooms, or about 0.002 psi. Nobody wants to write, say or scan that many decimal places all day. Water column keeps the numbers small enough to hold in your head: 7, 0.5, 0.05.
Water Gives You a Column You Can Actually See
Pressure lifts a column of liquid to a height that depends on how dense the liquid is. Water is fairly light, so it moves a lot for a small push. Mercury is 13.6 times denser, so it moves 13.6 times less. One psi lifts water about 27.7 inches but mercury only about 2 inches.
Run that on a real number. A gas supply at 7 inWC would show up as barely half an inch on a mercury manometer, which is hard to read by eye. On a water manometer it’s a clear 7 inches. Water is also cheap, safe to handle and easy to replace, which mercury is not.
The Physics Is Simple and Easy to Verify
A liquid column has no spring that can weaken, no diaphragm that can drift and no electronics that need calibrating. Height in, pressure out. A technician with a ruler and a length of tube can sanity-check a digital manometer, and that kind of trust is a big reason the unit stuck around.
Habit, Codes and Equipment Keep It Alive
Modern gauges are electronic, so nobody needs a tube of water to read low pressure anymore. The unit survived anyway. In the US, gas appliance ratings, HVAC static pressure targets, furnace manuals and ventilation guidelines are written in inWC, so the tools built to check them carry the same label. Switching would mean relabeling equipment, rewriting manuals and retraining a lot of technicians for no practical gain.
Outside the US, pascals and millibars play the same role, and the logic is identical: pick a unit sized for the job.
Water Column to PSI Conversion
Two formulas cover nearly every situation.
- To get psi from inWC, multiply by 0.03613 (or divide by 27.68).
- To get inWC from psi, multiply by 27.68.
Here are the values you’ll run into most often, with metric equivalents for good measure.
| inWC | psi | Pascals (Pa) | Millibar (mbar) | Where you might see it |
| 0.1 | 0.0036 | 24.9 | 0.25 | Draft, tiny differentials |
| 0.5 | 0.0181 | 124.5 | 1.25 | Duct static pressure |
| 1 | 0.0361 | 249.1 | 2.49 | Reference value |
| 2 | 0.0723 | 498.2 | 4.98 | Low airflow systems |
| 5 | 0.1806 | 1,245 | 12.5 | Low-pressure gas |
| 7 | 0.2529 | 1,744 | 17.4 | Natural gas supply |
| 11 | 0.3974 | 2,740 | 27.4 | Propane regulator output |
| 14 | 0.5058 | 3,487 | 34.9 | Half a psi |
| 27.68 | 1.0000 | 6,895 | 68.9 | One psi |
| 100 | 3.613 | 24,908 | 249 | Above most low-pressure work |
Worked Examples
A gas line delivers 7 inWC. Multiply 7 by 0.03613 and you get 0.253 psi, or about 4 ounces per square inch, which is how gas fitters often describe it.
A tire sits at 32 psi. Multiply by 27.68 and you get about 886 inWC. That’s the pressure at the bottom of a column of water roughly 74 feet tall.
A filter shows a 0.25 inWC pressure drop. That’s 0.009 psi, a figure that looks like nothing in psi and reads sensibly in inWC.
A few metric shortcuts are worth keeping handy:
- 1 inWC is about 249 Pa.
- 1 kPa is about 4.02 inWC.
- 1 cmH2O is about 98 Pa.
Where Each Unit Shows Up in Real Life
Typical values vary by region, equipment and code, so treat these as ballpark figures.
| Application | Typical value | Unit you’ll usually see | Converted |
| Residential natural gas supply | About 7 inWC | inWC | 0.25 psi |
| Propane at the appliance regulator outlet | About 11 inWC | inWC | 0.40 psi |
| Furnace or air handler duct static pressure | About 0.5 inWC | inWC | 0.018 psi |
| Cleanroom, room to room | 5 to 20 Pa (0.02 to 0.08 inWC) | Pa or inWC | 0.0007 to 0.003 psi |
| Hospital isolation room | At least 0.01 inWC (2.5 Pa) | Pa or inWC | 0.0004 psi |
| CPAP therapy | 4 to 20 cmH2O | cmH2O | 0.06 to 0.28 psi |
| Car tires | 32 to 35 psi | psi | 886 to 969 inWC |
| Home water supply | 40 to 80 psi | psi | 1,107 to 2,214 inWC |
Temperature, Gravity and Other Gotchas
A column of water only means something if you know what the water was doing. Water density changes with temperature, and gravity varies slightly from place to place, so the unit is defined at reference conditions. Some references define an inch of water at 4°C (39.2°F), where water is densest. Others use 60°F or 68°F.
The differences are small, about 0.1 to 0.2 percent between the common definitions. That’s why you’ll see 27.68 in one chart and 27.7 in another. For gas fitting and HVAC work you can ignore it. In a calibration lab it matters, and the reference temperature should be written down.
Then there’s the gauge versus absolute issue. Water column readings are almost always gauge or differential, meaning relative to the surrounding air. Atmospheric pressure at sea level works out to roughly 407 inWC absolute, which is a clumsy number for anything and a good reason nobody quotes absolute pressure in this unit.
How to Choose Between Water Column and PSI
Water column wins below about 1 psi. Past that, psi wins. The gray zone in between is small, so the choice is usually easy if you follow a few rules.
- Use water column when the pressure you care about is below about 1 psi (28 inWC). That covers gas appliances, ducts, drafts, room pressurization and most airflow work.
- Use psi once you’re past a few psi. Anything with a pump or compressor behind it belongs here.
- Work in whichever unit the spec, code or gauge face uses, and convert only at the end. Converting midway is how errors creep in.
- Pick an instrument whose scale ends not far above what you expect to read. A 0 to 30 psi gauge can’t tell you whether a gas line sits at 7 or 11 inWC, because both hover near the first tick mark.
Common Mistakes With Water Column and PSI
- Treating inWC as psi. Seven psi is nearly 28 times more than 7 inWC. Applying 7 psi to a gas valve built for 7 inWC will wreck it.
- Mixing up inWC and inHg. An inch of mercury is roughly 13.6 inches of water column, so the two aren’t interchangeable, even though both are inches of something.
- Over-pressurizing during leak tests. Codes generally require appliances to be disconnected when line test pressure goes above half a psi (about 14 inWC), since their regulators and valves aren’t built for it. Check your local code for the exact figures.
- Ignoring the sign. Chimney draft and negative-pressure rooms read below zero. A slightly negative flue reading is normal, and a positive one is a red flag.
- Mixing psig and psia. A tire gauge and a weather report are talking about different zeros.
Frequently Asked Questions
How many inches of water column equal 1 psi?
About 27.68 inWC. Some references round it to 27.7.
Is water column the same as water gauge?
Yes. inWC and inWG describe the same unit.
Why not use mercury instead of water?
Mercury is 13.6 times denser than water, so the column moves 13.6 times less for the same pressure, which makes small pressures hard to read. Mercury is also toxic, and many places have phased it out of instruments.
How many inWC are in a kPa?
About 4.02. One kPa is roughly 4.015 inWC.
What is 14 inWC in psi?
About 0.5 psi. The figure matters in gas piping because many appliance controls aren’t designed to see more.
Is water column a real unit of pressure?
Yes. It expresses pressure through height, and standards define it using a fixed water density, so it converts to pascals cleanly. One inWC at 4°C is about 249 Pa.
Content Disclaimer: The information on this page is provided for general educational and informational purposes only. While we aim to keep our content accurate and up to date, errors or omissions may occur. Information, specifications and other details can change, so always verify important information with the manufacturer or another reliable source before making a purchase or taking action.
