What Does “Height of Water Column” Mean in Pressure Measurement?

The height of water column is the vertical distance a column of water would rise when a pressure pushes on it. Instead of telling you a duct sits at 125 pascals, a technician says 0.5 inches of water column, and anyone who has ever sucked water up a straw has a feel for what that looks like. It’s pressure described as a height.
You’ll see it on furnace manuals, HVAC test sheets, pump curves, tank level transmitters and cleanroom monitors, written as inWC, mmH2O or mH2O. The numbers look odd until you know the trick behind them. This guide covers what the units mean, the one formula that ties them together, how to convert between them, how manometers and sensors read them, and the mistakes that catch out even experienced people.
Disclosure: This page may contain affiliate links. Please see our affiliate disclaimer for more information.
Quick answer: A height of water column is the pressure created by a vertical column of water of that height. One meter of water gives about 9.81 kPa. One inch gives about 249 Pa. The width or shape of the container doesn’t matter, only the vertical height.
Height of Water Column Explained in Plain English
Picture an upright clear tube, sealed at the bottom onto a pressure gauge. Pour in water and the gauge climbs. Fill it to 1 meter and you get a fixed, repeatable pressure. Fill it to 2 meters and you get exactly double.
Now run the idea backwards. Say you have an unknown pressure, like the air pushing through a heating duct. Connect it to a tube of water and it shoves the water down on one side and up on the other. The difference in levels is the pressure, stated as a height of water column. No electronics, no conversion tables, no battery. The measurement and the unit are the same physical thing, which is why the unit has outlived a century of gadgets.
Water became the standard because it’s cheap, safe, easy to see through a clear tube, and it moves a satisfying distance at low pressures. A gentle 100 Pa nudges a mercury column by about 0.75 mm, which you’d need a magnifying glass to read. The same pressure moves water by roughly 10 mm. For small pressures, water wins.
The Formula Behind the Height of Water Column
Every conversion in this guide comes from one line of physics:
P = ρ × g × h
- P is the pressure, in pascals (Pa)
- ρ (the Greek letter rho) is the density of the water, about 998 kg/m³ at room temperature
- g is gravitational acceleration, 9.80665 m/s²
- h is the height of water column, in meters
Flip it around and you get h = P ÷ (ρ × g), which turns any pressure into a height. That’s all a manometer does mechanically.
One detail trips up beginners. Only the vertical height counts. A skinny pipe 10 m tall and a wide pond 10 m deep produce the same pressure at the bottom. The pond holds far more water, but that weight is spread over a far bigger area, so the pressure on each square centimeter is identical.
Worked example: a 5 meter tank
A tank is filled to a depth of 5 m. The gauge pressure at the bottom is 5 × 9.80665 = 49.03 kPa, or about 7.1 psi. That’s gauge pressure, meaning it ignores the air pressing on the water surface. If you need absolute pressure, add roughly 101.3 kPa for the atmosphere.
Worked example: a blower reading 0.5 inWC
An HVAC technician measures 0.5 inWC across a blower. One inch of water column is about 249.09 Pa, so the reading is about 124.5 Pa, or 0.018 psi. Try saying 0.018 psi to a customer and watch their eyes glaze. Half an inch of water is easier to picture, and that’s the whole appeal.
Every additional 10 meters of water adds roughly 98 kPa, close to 1 bar.
Common Units for Height of Water Column and How to Convert Them
Four units cover almost everything you’ll meet. The metric ones show up in labs, process plants and level sensing. The imperial ones dominate North American HVAC and gas work.
| Unit | Common abbreviations | Value in pascals | Value in psi |
| Millimeter of water | mmH2O, mmWC | 9.807 Pa | 0.001422 psi |
| Inch of water column | inWC, in. w.c., inH2O | 249.09 Pa | 0.03613 psi |
| Foot of water | ftH2O, ft w.c. | 2,989 Pa | 0.4335 psi |
| Meter of water | mH2O, mWC | 9,806.65 Pa | 1.4223 psi |
You’ll also run into “w.g.” (water gauge) and plain “WC” on older equipment. They all mean the same thing. Strictly speaking, the exact value shifts a little depending on the water temperature chosen for the definition (4°C, 20°C or 60°F), but the spread is well under a quarter of a percent, which no furnace technician will ever notice.
Converting between pressure units and water column
| Pressure | Metric height of water column | Imperial height of water column |
| 1 kPa | 101.97 mmH2O | 4.015 inWC |
| 1 mbar (100 Pa) | 10.197 mmH2O | 0.4015 inWC |
| 1 psi | 703.07 mmH2O | 27.68 inWC |
| 1 bar | 10.197 mH2O | 401.5 inWC |
| 1 atm (101.325 kPa) | 10.33 mH2O | 406.8 inWC |
Mental math shortcuts
You don’t need a calculator for a quick sanity check. These five approximations get you within a couple of percent:
- 1 psi is about 27.7 inWC
- 1 inWC is about 250 Pa
- 1 mmH2O is about 10 Pa
- 1 kPa is about 100 mmH2O
- 10 meters of water is a touch under 1 bar (0.98 bar, to be exact)
Why Water Temperature Changes the Height of Water Column
Water gets lighter as it warms, so a meter of hot water pushes down less than a meter of cold water. The standard conversion value assumes water near its densest point, around 4°C. Here’s how much the real pressure per meter drifts as the temperature climbs.
| Water temperature | Density (kg/m³) | Pressure from 1 m of height | Compared with standard value |
| 4°C | 999.97 | 9,806 Pa | 100.0% |
| 20°C | 998.21 | 9,789 Pa | 99.8% |
| 40°C | 992.22 | 9,730 Pa | 99.2% |
| 60°C | 983.20 | 9,642 Pa | 98.3% |
| 80°C | 971.80 | 9,530 Pa | 97.2% |
For everyday ductwork or a cold-water tank you can ignore this. It starts to matter in two places: hot water heating loops, where a tall column of 80°C water pushes about 2.8% less than the textbook figure, and calibration work, where the temperature of the manometer fluid feeds straight into the error budget.
How the Height of Water Column Gets Measured
U-tube manometer
The classic instrument is a U-shaped tube part-filled with water. One leg connects to the pressure you’re measuring, the other stays open to the air. Whatever pressure you apply pushes one side down and the other up, and the gap between the two surfaces is your height of water column. Read it at eye level, and read the bottom of the meniscus. Water curls up against the glass, so the true level sits at the lowest point of the curve. Mercury does the opposite and domes, so with mercury you read the top.
Why not use mercury all the time? Mercury is about 13.6 times denser than water, so the same pressure moves it 13.6 times less. That’s perfect for large pressures (1 atm is only 760 mm of mercury versus 10.33 m of water) and useless for tiny ones.
Inclined manometer
When pressures are really small, a vertical tube barely moves. An inclined manometer lays the tube at a shallow angle so the liquid has to travel farther along the tube for the same vertical rise. At an angle of roughly 6 degrees, the scale stretches by a factor of about ten, which turns a 2 mm change into a 20 mm change you can actually read. Cleanroom and draft gauges lean on this trick.
Electronic sensors and level transmitters
Modern instruments skip the liquid altogether. A diaphragm flexes under pressure, and the sensor converts that flex into an electrical signal. Many of these devices still let you pick “mmH2O” or “inWC” on the display, because technicians think in those units.
Submersible level transmitters are the clearest example. Drop one to the bottom of a well or tank and it measures the pressure of the water above it. A sensor with a 0 to 10 mH2O range covers about 98 kPa, close to 1 bar, and reads a depth of up to 10 meters. Vented versions reference the atmosphere through their cable, so a passing storm front doesn’t fool the reading.
Where You’ll Run Into the Height of Water Column
| Where | Typical scale | What the number tells you |
| Gas furnace or boiler manifold | About 3.5 inWC (natural gas), around 10 inWC (propane) | Whether the burner gets the gas pressure it was designed for |
| Residential ductwork | Around 0.5 inWC total external static pressure | How hard the blower works against filters, coils and ducts |
| Cleanrooms and labs | Often 5 to 15 Pa between adjacent rooms | Which way air moves when a door opens |
| Water tanks and towers | 1 to 30 mH2O | Depth of water above the measuring point |
| Submersible level sensors | 0 to 10 mH2O is common | Liquid level, worked out from pressure at the bottom |
| Pumps | Head in meters or feet | How high the pump can lift the fluid |
HVAC and gas appliances
Duct systems live in tenths of an inch. A typical residential system is designed around 0.5 inWC of total external static pressure, and a clean filter eats only a fraction of that. Gas appliances are the same story: natural gas manifold pressure sits near 3.5 inWC and propane near 10 inWC. In psi those are 0.13 and 0.36. Nobody wants to write 0.126 psi on a service sheet, which is exactly why the water column unit survived. Adjusting gas pressure is a job for a licensed technician, but knowing what the number means helps you follow what they’re telling you.
Tanks, wells and level sensing
A hydrostatic level sensor is a pressure sensor wearing a different label. A reading of 3.2 mH2O means the water above the sensor is 3.2 m deep. For liquids heavier or lighter than water, divide the water column reading by the liquid’s specific gravity. A liquid with a specific gravity of 1.2 that produces 3.2 mH2O is really 2.67 m deep.
Pump head and water systems
Pump curves are printed in meters or feet of head, and head is the height of water column in disguise. The trick is that a centrifugal pump delivers the same head whatever the liquid, but the pressure changes with density. A pump producing 30 m of head gives about 294 kPa (42.7 psi) on water. Pump a liquid with a specific gravity of 1.2 and the same head gives about 353 kPa. That’s why engineers talk in head and let the density sort itself out later.
Mistakes That Skew Height of Water Column Readings
- Mixing up gauge and absolute pressure. A manometer open to the air reads gauge pressure. If a spec calls for absolute, add about 10.33 mH2O for sea-level atmosphere.
- Reading the wrong part of the meniscus. For water, read the bottom of the curve at eye level.
- Assuming tank shape or width matters. It doesn’t. Only the vertical distance from the free surface to the measuring point counts.
- Treating mmH2O and mbar as the same. They differ by a factor of about ten, since 1 mbar equals 10.2 mmH2O.
- Confusing inches of water with inches of mercury. One inHg is about 13.6 inWC.
- Forgetting temperature on hot systems. At 80°C the pressure per meter is nearly 3% lower than the standard figure.
- Leaving air bubbles in the tubing or letting a vertical manometer lean. Both push the reading off, and a leaning tube reads high because the liquid travels farther along the tube than it rises.
How to Convert a Height of Water Column to Pressure, Step by Step
- Write the height in meters. Multiply inches by 0.0254, feet by 0.3048, or millimeters by 0.001.
- Multiply the height in meters by 9,806.65 to get pascals.
- Divide by 1,000 for kilopascals, or by 6,894.757 for psi.
Try it with 12 inWC. That’s 12 × 0.0254 = 0.3048 m. Multiply by 9,806.65 and you get 2,989 Pa, which is 2.99 kPa or 0.4335 psi. You’ve just proved that 12 inches of water is the same as 1 foot of water, which is a nice check that the math holds together.
To go the other way, divide the pressure in pascals by 9,806.65 to get meters of water, then convert to whatever length unit you need.
Height of Water Column Quick Reference Chart
| Height of water column | Pressure (kPa) | Pressure (psi) |
| 1 inWC | 0.249 | 0.036 |
| 5 inWC | 1.245 | 0.181 |
| 10 inWC | 2.491 | 0.361 |
| 50 inWC | 12.454 | 1.806 |
| 1 mH2O | 9.807 | 1.422 |
| 5 mH2O | 49.03 | 7.112 |
| 10 mH2O | 98.07 | 14.22 |
| 30 mH2O | 294.2 | 42.67 |
Height of Water Column FAQ
Is height of water column the same as head?
They’re close relatives. Head is the same idea used for any liquid, expressed as a height of that liquid. Height of water column is head where the liquid happens to be water.
How many inches of water column equal 1 psi?
About 27.68 inches of water column. Going the other way, 1 inWC is roughly 0.036 psi.
Why do gas appliances use inches of water column instead of psi?
Their pressures are tiny. Natural gas at 3.5 inWC is only about 0.13 psi, and a regular psi gauge can’t show a difference that small. A water manometer or a low-range sensor can.
Can I use height of water column for liquids other than water?
Yes. Multiply the actual height of the liquid by its specific gravity to get the equivalent height of water column. Mercury, at a specific gravity of about 13.6, turns 1 mm of mercury into roughly 13.6 mmH2O.
Is 1 mmH2O the same as 1 mbar?
No. One millibar is 100 Pa, while one millimeter of water is about 9.8 Pa. Roughly 10.2 mmH2O make up 1 mbar, so mixing them up throws you off by a factor of ten.
How much water column equals one atmosphere?
One standard atmosphere supports about 10.33 meters, or 33.9 feet, of water. It’s the reason a suction pump sitting at the surface can’t draw water up from a well much deeper than about 10 meters, no matter how good the pump is.
Content Disclaimer: The information on this page is provided for general educational and informational purposes only. While we aim to keep our content accurate and up to date, errors or omissions may occur. Information, specifications and other details can change, so always verify important information with the manufacturer or another reliable source before making a purchase or taking action.
